|
|
| Dresser
|
|
E250/E300/E500
Wheel Parallel Dresser
BUY ONLINE
50A Matco Sine Dresser
BUY ONLINE
TDE GROMAX Vision Type
Angle & Radius Dresser
BUY ONLINE
TDB Radius & Angle
Dresser (Anteater)
BUY ONLINE
TDC GROMAX Wheel Dresser
BUY ONLINE
TDD GROMAX Duplex Dresser
BUY ONLINE
RD Rotary Wheel Dresser
BUY ONLINE
RDM Motor Rotary Wheel Dresser
BUY ONLINE
|
| |
|
TOP
|
| Wheel Parallel
Dresser |
|
| |
Features:
This
fine precision-made unit dresses
grinding wheels to any angle
from 0~60° with new smoothness and
accuracy |
Specifications:
| Center to center |
2" |
| Center tolerance |
0.0004" |
| Max. cross feed |
13/16" |
| Weight |
4
Lbs. |
|
| |
|
TOP
|
| GROMAX Vision
Type Angle & Radius Dresser |
|
| |
Features:
- Fixed
focus lens (3X)
- 1 vernier markings for dressing
- angle
- Magnification through hole
in the spindle makes it possible for operator to see how
to dress the form on the wheel
- Radius and angle can be done
perfectly tangent
- Accuracy within 0.0002"
|
Accuracy
within 0.0002". Satisfaction guarantee. |
 |
Specifications:
| Length |
81/4" |
| Height |
4" |
| Swing Arm |
180 |
| Max. Grinding
Wheel |
8"
dia. |
| Convex Radius |
5/8" |
| Concave Radius |
1" |
| Tangential Travel |
0.89" |
| Weight |
11
Lbs. |
|
Accessories:
| DS-030 |
Diamond Dresser
(ø1/4"x2") |
| DS-040 |
Diamond Dresser
(ø1/8"x2") |
| TDE-LNS |
Replacement
Optical Len |
|
| |
|
TOP
|
| Radius &
Angle Dresser (Anteater) |
|
| |
Features:
- Positive setting of
the diamond to absolute center with the special gage included
with the dresser
- Simple, fast, accurate radius
setting
- No height gage or other set-up
aids required
- Radius is set on the grinder
by measuring over the two pins or by inserting a gage block,
as shown, for direct reading
- Inside or outside radius is
determined simply by sliding the dowel pin to the right
for concave and to the left for convex
- 4x90° graduation in full 360°
circle
- 6 minute vernier reading.
Chrome plated
- One push-pull type knob for
radius and angle control and for safer and faster operations
- Accuracy: Extremely close
tolerances are held in the manufacture of this tool, assured
by hardening and precision grinding of all critical parts.
Ways are chrome hardened
- Economy: Set-up and dressing
time reduced to a bare minimum due to simplicity
|
Specifications:
| Max. wheel dia.
standard |
10" |
| Internal radii |
5/8"~15/8" |
| With rat-tail
adaptor |
1/32"~15/8" |
| External radii |
0~15/8" |
| Height from
base to center |
43/32" |
| Tangent travel
(either side of center) |
15/8" |
| Weight |
29
Lbs. |
|
Accessories:
Diamond Dresser
DS-010 (ø0.4"x3.15"/.2CT) |
|
Features:
- The wheel
dresser can dress 2 angles
tangent to a radius in one
continuous motion with .0001"
(0.002mm) accuracy
- The wheel dresser with a micrometer
feed 13/16" (38mm) travel
- Extremely accurate: Dress
2 angles tangent to a radius in one
continuous motion to within 0.0001"
- Fast and easy setups: Only
tools needed are a micrometer and a
wrench
- Setup to dress 2 angles takes
less than 15 seconds. 1 radius plus
2 angles in about 3 minutes
- Made of hardened & ground
tool steel
|
Specifications:
| Dressing
capacity |
up
to 8" wheel |
| Range
of convex radii |
0
~ 1.500" |
| Range
of concave radii |
0.030"
~ 1.500" |
| Height
to center of diamond |
61/2" |
| Overall
height |
7" |
| Base
dimensions |
43/4"x31/2"x11/4" |
| Weight |
20
Lbs. |
|
Accessories:
|
| |
|
TOP
|
| GROMAX Duplex
Dresser |
|
| |
Features:
- Dress both
sides of a grinding wheel precisely & simultaneously
- Made of hardened tool steel
HRC 60
|
Specifications:
| Max.
width of wheel |
19/16" |
| Max.
dressing depth |
19/16" |
| Max.
dressing width |
0.008" |
| Graduation |
0.001" |
|
Accessories:
| DS-030 |
Diamond Dresser
(ø1/4"x2"/.2CT) |
|
Features:
- Prolongs grinding
wheel's life
- Give true cutting surface
on a grinding wheel
- Easy to use and no set-up
down time
- Blaze-dried lacquer surface
finish
- Axis part is fixed with shaft
bearing for high speed rotation
- Ideal for CBN or diamond wheel
(Also known as braking dresser)
|
| |
|
TOP
|
| Motor Rotary
Wheel Dresser |
|
| |
Specifications:
| Length |
10.43" |
| Height |
3.46" |
| Diameter |
3.15" |
|
TOP
|
|
